#Cube pro cartridges manual#
You can find more information about the replacement of this cartridge in the manual below. Turn the wheel to ‘reset’ and press the wheel to confirm. Step 6: When installed with a Scale Control Meter, turn on the meter by pressing the wheel once. Flush the system with 20 litres of water until the water runs clear. Ventilate the system by opening the boiling water tap. Step 5: Turn on the mains water supply or stopcock and, if present, the inlet combination. Step 4: Screw in the new cartridge (clockwise). Step 3: Unscrew the old cartridge (counter clockwise). If an inlet combination is present, also close it. Turn off the mains water supply or stopcock. Dispense boiling and cold water together in order to release the pressure from the system and then close it when the water runs completely cold. Step 2: Press the on/off switch on the top of the tank.
#Cube pro cartridges plus#
You can check the lifespan of your Scale Control Plus in the document below ‘Determining Scale Control Plus cartridge lifespan UK’. When installed without a Scale Control Meter: when a certain amount of water has passed through the Scale Control Plus, the cartridge needs to be replaced. When the cartridge has been replaced, turn on the meter by pressing the wheel once and turn the wheel to ‘reset’. Snooze the alarm for 72 hours by pressing the wheel on the Scale Control Plus Meter. When installed with a Scale Control Meter: when alarm sounds and 0% flashes on the display. The Scale Control Plus has been developed to lengthen the lifespan of your Quooker by reducing the water hardness. Step 7: Press and hold the red button on top of the cartridge holder until the double-beep to reset timer. Step 6: Flush the filter by running 2 litres of water. Step 5: Turn on the water supply by opening the isolation valve (blue lever). Step 4: Screw in the new filter cartridge (clockwise). Step 3: Unscrew the old filter cartridge (counter clockwise). Step 2: Turn off the water supply by closing the isolation valve (blue lever). After replacing the cartridge, press the button for 5 seconds to reset the timer. The Cold Water Filter can be snoozed for 7 days by briefly pressing the red button on top of the cartridge holder. (Some older models have a 6 month timer). The alarm will beep and the LED will flash when the user dispenses filtered water after 12 months of use, indicating it’s time to replace the cartridge. The cartridge has a lifespan of 12 months. Step 4: Confirm that the filter has been replaced via the display on the CUBE, the counter restarts.Īctivated Carbon filter for use with the Cold Water Filter or Quooker Water Switch which ensures the water tastes and smells better. Step 3: Screw in the new CUBE cartridge firmly until they cannot be tightened any further (clockwise). Step 2: Unscrew the old CUBE cartridge (counter clockwise). Step 1: Order your new filter cartridge in our webshop. After your approval, the 12-month counter restarts. The CUBE will then ask you whether you have replaced the filter.
If you have replaced the filter, go to ‘filter’ on the display and click on it. During this time, you can order a new cartridge in our webshop. This signal can be snoozed for 72 hours using the snooze button on the display. If the filter is saturated, the CUBE displays a message on the display and emits a beeping signal. For hygienic reasons, the cartridge should be replaced every 12 months, regardless of the amount of water used. Both filters together ensure a better water quality because they filter bacteria, chloride, chemicals and pesticides from the water. The CUBE is equipped with a dual Active Carbon filter and a Hollow Fibre filter. You can find more information about this filter in the datasheet below. Step 5: Press and hold the red button below the sliding panel on top of the CUBE for 6 seconds to reset the timer. Press down firmly until you hear a ‘click’. Step 4: Place the cartridge holder back into in the CUBE. Step 3: Screw in the new CUBE cartridges firmly until they cannot be tightened any further (clockwise). Step 2: Unscrew the old CUBE cartridges (counter clockwise). Step 1: Order your new cartridge in our webshop. The red light will go out and the beeping sound will stop temporarily. Briefly press the red flashing button below the sliding panel on top of the CUBE.
During this time, you can order a new filter set in our webshop. When the CUBE starts to beep, it is time for new filters. For hygienic reasons, the filters should be replaced every 12 months, regardless of the amount of water used.
The CUBE is equipped with an Active Carbon filter and a Hollow Fibre filter.
0 kommentar(er)
